Electric Hoist
Manual Hoist
Trolley
Lifting Clamps
Materials Handling
Crane Series

Related

"Wire Rope Winch"

Products
SHA OPEN WINCH
2014-04-23

Email: sales@liftech-equipment.com

HAND WINCH
2013-12-09

Email: sales@liftech-equipment.com

WRW
2013-12-09

Email: sales@liftech-equipment.com

Electric Winch
2014-04-23

Email: sales@liftech-equipment.com

Related

"Wire Rope Winch"

Blog
Wire rope winch maintenance measures
2014-11-01
Every job is completed, the first on the loose end of the rope to wipe adhesion mud, dust or oil, loosen the jaw, out of the rope, the rope in order to collect around the shelves, and wipe a total length of wire rope, wire rope stored in a dry place , to prevent corrosion. Respond Wire rope winch at least four times a maintenance treatment, such a... Every job is completed, the first on the loose end of the rope to wipe adhesion mud, dust or oil, loosen the jaw, out of the rope, the rope in order to collect around the shelves, and wipe a total length of wire rope, wire rope stored in a dry place , to prevent corrosion. Respond Wire rope winch at least four times a maintenance treatment, such as clean diesel parts, and calcium-based grease lubricated annually. When the internal movement poured mud, cement or other dirt, rinse with water, then clean diesel; cleaning, the calcium-based grease grease dried; finally release the jaw, wipe with a clean cotton on the jaw grease and moisture. Wire rope winch jaw when worn, the bearing capacity of less than 80% of rated load, replace the jaw, when the rope diameter decreases 10%, the rope should be replaced. View Details
Liftech Equipment Wire rope winch deformation of the main factors
2014-10-23
Liftech Equipment Wire rope winch deformation there are three main factors: trauma, crushing, kinking. This is primarily due to three factors that people use the right middle of the operation caused. Wire rope winchTrauma. This is mainly in the course of the rope with the other devices is not normal due to the contact, occurs in most cases is the ... Liftech Equipment Wire rope winch deformation there are three main factors: trauma, crushing, kinking. This is primarily due to three factors that people use the right middle of the operation caused. Wire rope winchTrauma. This is mainly in the course of the rope with the other devices is not normal due to the contact, occurs in most cases is the rope pulleys in the chute, out of the baffle on the roll, both of which often makes the rope because dozens m rolling bad result overall scrapped. Ways to improve this situation is to improve the lifting equipment, first pulley groove should set a reliable slip ring, while on the rope reel should not be too much slack, prevent the rope out of the rolling shutter causes bad. Roll each rope is easy to roll on roll chaos after chaos, mutual strife, the sound when using that appear broken wire or rope partial flattening marks. This should be in accordance with the selection criteria pulley and roll angle can also be set up rows of thread or cord compression device to prevent the rope volumes appear chaotic phenomenon. Kink. Twisted rope due to local produce permanent deformation is rope kink. After the kink rope strength will significantly reduce damage, affecting the normal use of wire rope. We should pay attention to the care and maintenance of wire rope in daily use, reducing unnecessary losses. View Details
wire rope winch will overload debugging
2014-01-21
                                       In the production of manual hoist design, in order to facilitate the actual operation , usually with overload means wire rope winch for limiting the development of the debugger , the program quenched what it sho...                                        In the production of manual hoist design, in order to facilitate the actual operation , usually with overload means wire rope winch for limiting the development of the debugger , the program quenched what it should be noted that ? First, to improve the accuracy and simplify debugging values generally in the debugger uses electronic crane to facilitate simplify configuration counterweight block ; Second phase should focus on in the run before the whole assembly , conditions can be configured ergometer , positioning and control systems in order to establish the running test bench reduce the intensity of the work to improve the overall efficiency ; hoists for load limit load used to debug , try to set a different interval , the same specifications used when debugging the greater the slip load values decreased slightly ; limits set debugging is not a substitute gourd factory dynamic load test , two different emphases , load requirements are also different. Master the methods above points , easy to get manual hoist overload debugging.                                     View Details
In recent years, wire rope winch is used for floating roof tanks were frequent
2014-01-21
                                       In recent years, construction hoist is used for floating roof tanks gradually frequently choose to use wire rope winch be floating roof tank construction , because it is its applicability, especially electric ho...                                        In recent years, construction hoist is used for floating roof tanks gradually frequently choose to use wire rope winch be floating roof tank construction , because it is its applicability, especially electric hoist downInstallation method in the field to better highlight its advantages. Flip electric hoist has obvious advantages and applicability , especially for floating roof tank construction , upgrading flip method for 10,000 m3External floating roof tank , floating roof tank construction requirements, maintenance inconvenience , choose low-speed smooth gourd work under normal circumstances .Flip electric hoist method is more secure, stable , easy to adjust , enhance each lap siding completed just 3-5min . No aerial , safe and reliable construction , tank wall groupWelding were carried out on the ground , low intensity boss , do not use heavy lifting equipment ( Wire rope winch) .Applicability , construction without water restrictions . Easy control panel deformation and ensure the accuracy of the tank geometry , thus ensuring the quality of welding panels to avoid water-filled dressAnd other processes is not conducive to the control panel ( in particular sheet ) deformation of the shortcomings. Floating roof phased production, has little effect on the tank construction , ease of operation and lines cross each process forIndustry , electric hoist flip method to improve the efficiency of labor and equipment, equipment efficiency.                                     View Details
Guide line of wire rope winch design thinking
2014-01-20
                                       The role of the drum is used for winding wire rope in the lifting mechanism, transfer the power, and the rotation movement into linear motion. Drum surface usually cut out of the spiral groove, the helix Angle i...                                        The role of the drum is used for winding wire rope in the lifting mechanism, transfer the power, and the rotation movement into linear motion. Drum surface usually cut out of the spiral groove, the helix Angle is wire rope winch in commonly 3 & deg; - 4 & deg; , increase the contact area of the wire rope, and prevent the friction between adjacent wire rope, improve the service life of wire rope. Because of the drum cutting out spiral groove guide line function, make the steel wire rope can be lined up. But often in the absence of other auxiliary body synergy, winding rope on the drum will jump out of the spiral groove, wire rope row disorderly; Sometimes in the gaps in the drum ends of the wire rope will be extrusion deformation; Will have the wire rope skipping a few spiral groove; Irregular arrangement, can make the steel wire rope, drum wear deformation; In short this will affect the use of the drum and wire rope, so as to shorten the service life of the crane. In order to make the wire rope on the drum lined up, extend the service life of the body parts, a lot of crane manufacturers are installed as shown in the guide rope device accordingly. Shown in the guide rope device is because of the interaction between wire rope and the guide rope mouth, guide line and reel contact friction, will increase the steel wire rope and drum wear. Install such guide line device of the crane because of site operation staff sometimes not according to the use of standardized operation (e.g., oblique, lateral lifting heavy weights), rope guide is often bad, cannot work in crane, affect the normal production. In order to avoid the happening of this kind of thing, can use drum helical groove can make the steel wire rope groove around the function, design a simple structure of the guide rope, the rope guide to put on my company's factory crane, use after user reaction effect is very good.                                     View Details